Series N140F
Pota-Pox Plus
Generic Type
Polyamidoamine Epoxy
Common Usage
Innovative potable water coating which offers high-build edge protection and allows for application at a wide range of temperatures (down to 35°F or 2°C). For use on the interior and exterior of steel or concrete tanks, reservoirs, pipes, valves, pumps and equipment in potable water service.
Special Qualifications
Certified by NSF International in accordance with ANSI/NSF Std. 61. Series N140F manufactured by Tnemec Company in Kansas City, Missouri or Baltimore, Maryland; ambient air cured (with or without 44-700 Epoxy Accelerator) is qualified for use on tanks and reservoirs of 1,000 gallons (3,785 L) capacity or greater, pipes 18 inches (46 cm) in diameter or greater, valves four (4) inches (10 cm) in diameter or greater and fittings four (4) inches (10 cm) in diameter or greater. Series N140F manufactured by Tnemec Coatings in Shanghai, China; ambient air cured (with or without 44-700 Epoxy Accelerator) is qualified for use on pipes 18 inches (46 cm) in diameter or greater, valves four (4) inches (10 cm) in diameter or greater and fittings four (4) inches (10 cm) in diameter or greater. Reference Tnemec’s certified product listing at www.nsf.org for details on the maximum allowable DFT.
Conforms to AWWA D 102 Inside Systems No. 1 and No. 2 (with or without 44-700). Conforms to AWWA C 210
(without 44-700). Contact your Tnemec representative for systems and additional information.
Product Data Sheets
- English_Series_N140F_Pota_Pox_Plus_pds.pdf
- French_Series_N140F_Pota_Pox_Plus_pds.pdf
- Spanish_Series_N140F_Pota_Pox_Plus_pds.pdf
Safety Data Sheets
Email this productContact your sales reps for quotes, problem solving advice, extensive technical knowledge, pricing, ordering and field support.
Colors
View Available Colors
View available colors in our Color Tool; you can also select and request color swatches.
Number of Components
Two: Part A (amine) and Part B (epoxy) — One (Part A) to one (Part B) by volume.
Topcoats
Interior: Series 22, FC22, L140, L140F, N140, N140F, V140, V140F, 141, 406
Exterior: Series 22, 27, 27WB, 30, 66, L69, L69F, N69, N69F, V69, V69F, 72, 73, 118, L140, L140F, N140, N140F, V140, V140F, 141, 156, 157, 161, 180, 181, 446, 700, V700, 701, V701, 740, 750, 1026, 1028, 1029, 1074, 1074U, 1075, 1075U, 1077, 1078, 1078V, 1080, 1081, 1094, 1095, 1096, 1224. Note: When topcoating with Series 700, V700, 701, or V701, an intermediate coat of Series 73, 1075, 1075U, 1095 or 1096 is required. Note: The following recoat times apply for Series N140F: Immersion Service—Surface must be scarified by blasting with fine abrasive after 30 days. Atmospheric Service—After 30 days, scarification or an epoxy tie-coat is required. When topcoating with Series 740 or 750, recoat time for N140F is 14 days. Note: When topcoating with Series 406, recoat times will vary with temperature. Reference the Series 406 product data sheet for specific recoat times. Contact your Tnemec representative for specific recommendations.
Volume Solids
68.0 ± 2.0% (mixed) †
Volatile Organic Compounds
Unthinned: 2.3 lbs/gallon (273 grams/litre)
Thinned 5% (#60): 2.5 lbs/gallon (299 grams/litre)
Thinned 10% (#4): 2.7 lbs/gallon (323 grams/litre) †
Recommended DFT
2.0 to 10.0 mils (50 to 225 microns) per coat. Note: Dry film thickness that exceeds published recommendations but is in compliance with SSPC PA-2 and ANSI/NSF Std. 61 certifications, is acceptable. Note: The number of coats and thickness requirements will vary with substrate, application method and exposure. Contact your Tnemec representative.
Theoretical Coverage
1,094 mil sq ft/gal (26.8 m²/L at 25 microns). See APPLICATION for coverage rates. †
HAPS
Unthinned: 2.3 lbs/gal solids
Thinned 5% (#60): 2.3 lbs/gal solids
Thinned 10% (#4): 3.1 lbs/gal solids
Still have questions? Request the information you’re looking for:
Request InfoHow to Purchase
Tnemec coatings are sold through a select network of local independent sales representatives who can help you find the best product for your needs. Find a rep