Innovative potable water coating which offers high-build edge protection and allows for application at a wide range of temperatures (down to 35°F or 2°C with 44-700 Accelerator). For use on the interior and exterior of steel or concrete tanks, reservoirs, pipes, valves, pumps and equipment in potable water service.
Certified by NSF International in accordance with ANSI/NSF Std. 61. Series N140 manufactured by Tnemec Company in Kansas City, Missouri or Baltimore, Maryland; ambient air cured (with or without 44-700 Epoxy Accelerator) is qualified for use on tanks and reservoirs of 1,000 gallons (3,785 L) capacity or greater, pipes 18 inches (46 cm) in diameter or greater, valves four (4) inches (10 cm) in diameter or greater and fittings four (4) inches (10 cm) in diameter or greater. Series N140 manufactured by Tnemec Coatings in Shanghai, China; ambient air cured (with or without 44-700 Epoxy Accelerator) is qualified for use on pipes 18 inches (46 cm) in diameter or greater, valves four (4) inches (10 cm) in diameter or greater and fittings four (4) inches (10 cm) in diameter or greater.
Certified by NSF International in accordance with NSF/ANSI/CAN Std. 61 and the extraction requirements of NSF/ANSI/CAN 600 for use as a primer or intermediate coat with any Tnemec NSF certified primer and topcoat coating system provided the primer, intermediate and topcoat meet their certified end uses. Series N140 is qualified for use on tanks and reservoirs of 500 gallons (1892 L) capacity or greater. Reference Tnemec’s certified product listing at www.nsf.org for details on the maximum allowable DFT.
Conforms to AWWA D102 Inside Systems No. 1 and No. 2 (with or without 44-700). Conforms to AWWA C210 (without 44-700). Contact your Tnemec representative for systems and additional information.
A two-coat and three-coat system of Series N140 meets the requirements of AWWA C550 Protective Interior Coatings for Valves and Hydrants.View more product details
Product Data Sheets
Safety Data SheetsEmail this product
Number of Components
Two: Part A (amine) and Part B (epoxy) — One (Part A) to one (Part B) by volume.
Unthinned: 2.4 lbs/gal solids Thinned 5% (#60): 2.4 lbs/gal solids
Thinned 10% (#4): 3.3 lbs/gal solids
2.0 to 10.0 mils (50 to 225 microns) per coat. Note: Dry film thickness that exceeds published recommendations but is in compliance with SSPC PA-2 and ANSI/NSF Std. 61 certifications, is acceptable. Note: The number of coats and thickness requirements will vary with substrate, application method and exposure. Contact your Tnemec representative.
1,070 mil sq ft/gal (27.2 m²/L at 25 microns). See APPLICATION for coverage rates. †
67.0 ± 2.0% (mixed—A, B & 44-700 Epoxy Accelerator) †
Volatile Organic Compounds
Unthinned: 2.4 lbs/gallon (285 grams/litre)
Thinned 5% (#60): 2.6 lbs/gallon (311 grams/litre)
Thinned 10% (#4): 2.8 lbs/gallon (334 grams/litre) †
Interior: Series 22, FC22, L140, L140F, N140, N140F, V140, V140F, 141, 264, 265, 406.
Exterior: Series 22, 27, 27WB, 30, 66, L69, L69F, N69, N69F, V69, V69F, 72, 73, 118, L140, L140F, N140, N140F, V140, V140F, 141, 156, 157, 161, 180, 181, 446, 700, V700, 701, V701, 740, 750, 1026, 1028, 1029, 1074, 1074U, 1075, 1075U, 1077, 1078, 1078V, 1080, 1081, 1094, 1095, 1096, 1224. Note: When topcoating with Series 700, V700, 701 or V701, an intermediate coat of Series 73, 1075, 1075U, 1095 or 1096 is required. Note: The following recoat times apply for Series N140: Immersion Service—Surface must be scarified by blasting with fine abrasive after 60 days. Atmospheric Service—After 60 days, scarification or an epoxy tie-coat is required. When topcoating with Series 740 or 750, recoat time for N140 is 21 days. Note: When topcoating with Series 406, recoat times will vary with temperature. Reference the Series 406 product data sheet for specific recoat times. Contact your Tnemec representative for specific recommendations.
Still have questions? Request the information you’re looking for:Request Info
How to Purchase
Tnemec coatings are sold through a select network of local independent sales representatives who can help you find the best product for your needs. Find a rep