Series N69F | Hi-Build Epoxoline II

Generic Type Polyamidoamine Epoxy
Common Usage An advanced generation epoxy for the protection and finishing of steel and concrete. It has excellent resistance to abrasion and is suitable for immersion as well as chemical contact exposure. Contact your local Tnemec representative for a list of chemicals. This product can also be used as a block filler on cementitious or masonry substrates.
Colors Limited color availability. Contact your Tnemec representative.
Finish Satin
Surfacer/Filler/Patcher 215
Primers Steel: Self-priming or Series 1, 27, 37H, 66, L69, L69F, N69, V69, 90E-92, 90G-1K97, 90-97, H90-97, 90-98, 91-H2O, 94-H2O, 135, 161, 394, 530
Galvanized Steel and Non-Ferrous Metal: Self-priming or Series 66, L69, L69F, N69, V69, 161
Concrete: Self-priming or Series 130, 215, 218
CMU: Self-priming or Series 130, 215, 218, 1254
Topcoats 22, 46H-413, 66, L69, L69F, N69, N69F, V69, V69F, 72, 73, 84, 104, 113, 114, 141, 156, 157, 161, 175, 180, 181, 287, 446, 740, 750, 1028, 1029, 1070, 1070V, 1071, 1071V, 1072, 1072V, 1074, 1074U, 1075, 1075U, 1077, 1078, 1080, 1081. Refer to COLORS on applicable topcoat data sheets for additional information. Note: The following recoat times apply for Series N69F: Immersion Service—Surface must be scarified after 30 days. Atmospheric Service—After 30 days, scarification or an epoxy tie-coat is required. When topcoating with Series 740 or 750, recoat time for N69F is 14 days. Contact your Tnemec representative for specific recommendations.
Volume Solids 69.0 ± 2.0% (mixed) †
Recommended DFT 2.0 to 10.0 mils (50 to 255 microns) per coat. Note: The number of coats and thickness requirements will vary with substrate, application method and exposure. Contact your Tnemec representative.
Volatile Organic Compounds Unthinned: 2.30 lbs/gallon (280 grams/litre)
Thinned 10% (No. 4 Thinner): 2.75 lbs/gallon (330 grams/litre)
Thinned 10% (No. 60 Thinner): 2.76 lbs/gallon (331 grams/litre)

HAPS Unthinned: 2.35 lbs/gal solids
Thinned 10% (No. 4 Thinner): 3.20 lbs/gal solids
Thinned 10% (No. 60 Thinner): 2.35 lbs/gal solids

Theoretical Coverage 1,107 mil sq ft/gal (27.2 m²/L at 25 microns). See APPLICATION for coverage rates. †
Number of Components Two: Part A (amine) and Part B (epoxy) — One (Part A) to one (Part B) by volume.

The products listed below are not exact equivalents. They are only products that you may consider as alternatives in a general sense. Substrate type, condition, temperatures, surface preparation, primer/topcoat selection and intended use are just a few factors that will affect product selection. Please contact your local Tnemec Coatings Consultant for product recommendations.

This ProductPolyamidoamine Epoxy
Volume SolidsRec. DFTV.O.C.# of Components
69.0 ± 2.0% (mixed) †2.0 to 10.0 mils (50 to 255 microns) per coat. Note: The number of coats and thickness requirements will vary with substrate, application method and exposure. Contact your Tnemec representative.Unthinned: 2.30 lbs/gallon (280 grams/litre)
Thinned 10% (No. 4 Thinner): 2.75 lbs/gallon (330 grams/litre)
Thinned 10% (No. 60 Thinner): 2.76 lbs/gallon (331 grams/litre)

Two: Part A (amine) and Part B (epoxy) — One (Part A) to one (Part B) by volume.
Series V69F | Hi-Build Epoxoline II Polyamidoamine Epoxy
Hide this product's data
Volume SolidsRec. DFTV.O.C.# of Components
69.0 ± 2.0% (mixed) †2.0 to 10.0 mils (50 to 255 microns) per coat. Note: The number of coats and thickness requirements will vary with substrate, application method and exposure. Contact your Tnemec representative.Unthinned: 1.90 lbs/gallon (228 grams/litre)
Thinned 3.5% (No. 4 Thinner): 2.08 lbs/gallon (250 grams/litre) †
Two: Part A (amine) and Part B (epoxy) — One (Part A) to one (Part B) by volume.

Series N69F Hi-Build Epoxoline II was used as one of the primers for the Portland, ME International Jetport Parking Garage.