find your coatings consultants
Find and contact a coatings consultant near you.

Series N140 | Pota-Pox Plus

Generic Type Polyamidoamine Epoxy
Common Usage Innovative potable water coating which offers high-build edge protection and allows for application at a wide range of temperatures (down to 35°F or 2°C with 44-700 Accelerator). For use on the interior and exterior of steel or concrete tanks, reservoirs, pipes, valves, pumps and equipment in potable water service.
Colors 1211 Red, 1255 Beige, 00WH Tnemec White, 15BL Tank White, 35GR Black and 39BL Delft Blue. Note: Epoxies chalk with extended exposure to sunlight. Lack of ventilation, incomplete mixing, miscatalyzation or the use of heaters that emit carbon dioxide and carbon monoxide during application and initial stages of curing may cause yellowing to occur.
Surfacer/Filler/Patcher 215, 217, 218
Primers Self-priming, 22, 91-H2O, 94-H2O, L140, L140F, N140F, V140, V140F, 141
Topcoats Interior: Series 22, FC22, L140, L140F, N140, N140F, V140, V140F, 141, 406.
Exterior: Series 27, 66, L69, L69F, N69, N69F, V69, V69F, 72, 73, L140, L140F, N140, N140F, V140, V140F, 156, 157, 161, 175, 180, 181, 446, 740, 750, 1028, 1029, 1074, 1074U, 1075, 1075U, 1077, 1078, 1080, 1081. Refer to COLORS on applicable topcoat data sheets for additional information. Note: The following recoat times apply for Series N140: Immersion Service—Surface must be scarified by blasting with fine abrasive after 60 days. Atmospheric Service—After 60 days, scarification or an epoxy tie-coat is required. When topcoating with Series 740 or 750, recoat time for N140 is 21 days. Contact your Tnemec representative for specific recommendations.
Volume Solids 67.0 ± 2.0% (mixed—A, B & 44-700 Epoxy Accelerator) †
Recommended DFT 2.0 to 10.0 mils (50 to 225 microns) per coat. Note: MIL-PRF-4556F applications require two coats at 4.0-6.0 mils (100-150 microns) per coat. Otherwise, the number of coats and thickness requirements will vary with substrate, application method and exposure. Contact your Tnemec representative.
Volatile Organic Compounds Unthinned: 2.4 lbs/gallon (285 grams/litre)
Thinned 5% (#60): 2.6 lbs/gallon (311 grams/litre)
Thinned 10% (#4): 2.8 lbs/gallon (334 grams/litre) †
HAPS Unthinned: 2.4 lbs/gal solids Thinned 5% (#60): 2.4 lbs/gal solids
Thinned 10% (#4): 3.3 lbs/gal solids
Theoretical Coverage 1,070 mil sq ft/gal (27.2 m²/L at 25 microns). See APPLICATION for coverage rates. †
Number of Components Two: Part A (amine) and Part B (epoxy) — One (Part A) to one (Part B) by volume.
1
Category
2
Chemical Name(required)
3
Concentration
4
What is this?

Note: Not Recommended (NR), Not Tested (NT), Please Call (PC)

 

Chemical Recommended Use - What is this?

The chemical resistance data listed on this website should only be used for general reference purposes. Substrates, temperatures, chemical combinations, and other variables can affect the performance of a coating in chemical exposure. Please contact your local to finalize the most appropriate system for your project.

Click the following button to download a PDF of the list of chemicals below.

*Results are NOT suitable for direct or indirect food contact. Intended use exposure results relate to product's performance and substrate protection capabilities only.


Recommended Use
Chemical <90°F (32°C) 90-120°F
(32-49°C)
120-140°F
(49-60°C)
140-160°F
(60-71°C)
160-180°F
(71-82°C)
180-200°F
(82-93°C)
200-220°F
(93-104°C)
*Results are NOT suitable for direct or indirect food contact. Intended use exposure results relate to product's performance and substrate protection capabilities only.
  • Color cards, swatches and fan decks are offered at no charge, by request , for more accurate color selection. Expert custom color matching is also available by contacting your Tnemec Coatings Consultant .
  • Deeptone colors may be more expensive than lighter colors. Please contact your Tnemec Coatings Consultant to verify product/color availability and pricing.

Products Available In Black 35GR

Black| 35GR (formerly IN06) rgb 18,18,18
Request a Swatch Swatch Unavailable
These digital colors should not be used to finalize your color selection. Please read our disclaimer . Use the color swatch tool on the left to request official color swatches.

Color Swatch Packet

Request another

(maximum 6 color swatches)

You haven't added any color swatches to your packet. Select some colors now by clicking a color above and then clicking the 'Request a Swatch' button on the color.

The products listed below are not exact equivalents. They are only products that you may consider as alternatives in a general sense. Substrate type, condition, temperatures, surface preparation, primer/topcoat selection and intended use are just a few factors that will affect product selection. Please contact your local Tnemec Coatings Consultant for product recommendations.

This ProductPolyamidoamine Epoxy
Volume Solids Rec. DFT V.O.C. # of Components
67.0 ± 2.0% (mixed—A, B & 44-700 Epoxy Accelerator) † 2.0 to 10.0 mils (50 to 225 microns) per coat. Note: MIL-PRF-4556F applications require two coats at 4.0-6.0 mils (100-150 microns) per coat. Otherwise, the number of coats and thickness requirements will vary with substrate, application method and exposure. Contact your Tnemec representative. Unthinned: 2.4 lbs/gallon (285 grams/litre)
Thinned 5% (#60): 2.6 lbs/gallon (311 grams/litre)
Thinned 10% (#4): 2.8 lbs/gallon (334 grams/litre) †
Two: Part A (amine) and Part B (epoxy) — One (Part A) to one (Part B) by volume.
Series V140 | Pota-Pox Plus Polyamidoamine Epoxy
Hide this product's data
Volume Solids Rec. DFT V.O.C. # of Components
67.0 ± 2.0% (mixed—A, B & 44-700 Epoxy Accelerator) † 2.0 to 10.0 mils (50 to 225 microns) per coat. Note: MIL-PRF-4556F applications require two coats at 4.0-6.0 mils (100-150 microns) per coat. Otherwise, the number of coats and thickness requirements will vary with substrate, application method and exposure. Contact your Tnemec representative. Unthinned: 1.95 lbs/gallon (234 grams/litre)
Thinned 2.5% (#4): 2.08 lbs/gallon (250 grams/litre) †
Two: Part A (amine) and Part B (epoxy) — One (Part A) to one (Part B) by volume.