find your coatings consultants
Find and contact a coatings consultant near you.

Series 750 | UVX

Generic Type Modified Polycarbamide
Common Usage An advanced technology finish coat combining low VOC with exceptional performance. Offers superior color and gloss retention compared to traditional polyurethanes for long-term aesthetics on a wide range of exterior structures. Durable film stands up to exterior weathering. Very good brush, roll and spray application characteristics. NOT FOR IMMERSION SERVICE.
Colors Refer to Tnemec Color Guide. Note: Certain colors may require multiple coats depending on method of application and finish coat color. When feasible, the preceding coat should be in the same color family (blue, gray, etc.), but noticeably different.
Finish Semi-gloss
Primers Steel: Series 1, 27, 27WB, 66, L69, L69F, N69, N69F, V69, V69F, 73, 90G-1K97, 90-97, H90-97, 91-H2O, 94-H2O, 135, L140, L140F, N140, N140F, V140, V140F, 161, 394, 1075
Concrete: Series 1, 27, 27WB, 66, L69, L69F, N69, N69F, V69, V69F, 161, 1254
Note: Series 66, L69, N69, V69, 135, L140, N140, or V140 exposed more than 21 days; Series 27, 161, L69F, N69F, V69F, L140F, N140F, or V140F exposed more than 14 days; and Series 27WB, 73, or 1075 exposed more than 90 days must first be scarified or reprimed with themselves (or with an epoxy for 73 and 1075) prior to topcoating. Brush blasting with fine abrasive is the preferred method of scarification.
Topcoats Series 700, V700, 701, V701, 740, 1070, 1070V, 1071, 1071V, 1072, 1072V, 1077, 1078
Note: When topcoating Series 750 with itself, or any of the above listed topcoats, the maximum recoat time is 45 days.
Volume Solids 72.0 ± 2.0% (mixed) †
Recommended DFT 2.5 to 5.0 mils (65 to 125 microns) per coat. Note: Number of coats and thickness requirements will vary with substrate, application method and exposure. Contact your Tnemec representative.
Curing Time
TemperatureTo TouchTo HandleTo RecoatTo Resist Moisture
75°F (24°C)2 hours6-8 hours8 hours13 hours
Curing time varies with surface temperature, air movement, humidity and film thickness. Note: For faster time-to-moisture resistance and low-temperature applications, add No. 44-712 Urethane Accelerator; see separate product data sheet.
Volatile Organic Compounds Unthinned: 0.82 lbs/gallon (99 grams/litre)
Thinned 10% (No. 68 Thinner): 0.82 lbs/gallon (99 grams/litre)
Thinned 10% (No. 49 Thinner): 0.82 lbs/gallon (99 grams/litre) †
HAPS Unthinned: 0 lbs/gal solids
Thinned 10% (No. 68 Thinner): 0 lbs/gal solids
Thinned 10% (No. 49 Thinner): 0 lbs/gal solids
Theoretical Coverage 1155 mil sq ft/gal (28.3 m²/L at 25 microns) †
Number of Components Two: Part A and Part B
1
Category
2
Chemical Name(required)
3
Concentration
4
What is this?

Note: Not Recommended (NR), Not Tested (NT), Please Call (PC)

 

Chemical Recommended Use - What is this?

The chemical resistance data listed on this website should only be used for general reference purposes. Substrates, temperatures, chemical combinations, and other variables can affect the performance of a coating in chemical exposure. Please contact your local to finalize the most appropriate system for your project.

Click the following button to download a PDF of the list of chemicals below.

*Results are NOT suitable for direct or indirect food contact. Intended use exposure results relate to product's performance and substrate protection capabilities only.


Recommended Use
Chemical Occasional Contact Frequent Contact Secondary Containment Cargo Immersion Immersion Service
*Results are NOT suitable for direct or indirect food contact. Intended use exposure results relate to product's performance and substrate protection capabilities only.
  • Color cards, swatches and fan decks are offered at no charge, by request , for more accurate color selection. Expert custom color matching is also available by contacting your Tnemec Coatings Consultant .
  • Deeptone colors may be more expensive than lighter colors. Please contact your Tnemec Coatings Consultant to verify product/color availability and pricing.

Products Available In Vapor Mist 01GR

Vapor Mist| 01GR rgb 211,211,216
Request a Swatch Swatch Unavailable
These digital colors should not be used to finalize your color selection. Please read our disclaimer . Use the color swatch tool on the left to request official color swatches.

Color Swatch Packet

Request another

(maximum 6 color swatches)

You haven't added any color swatches to your packet. Select some colors now by clicking a color above and then clicking the 'Request a Swatch' button on the color.

The products listed below are not exact equivalents. They are only products that you may consider as alternatives in a general sense. Substrate type, condition, temperatures, surface preparation, primer/topcoat selection and intended use are just a few factors that will affect product selection. Please contact your local Tnemec Coatings Consultant for product recommendations.

This ProductModified Polycarbamide
Volume Solids Rec. DFT V.O.C. # of Components
72.0 ± 2.0% (mixed) † 2.5 to 5.0 mils (65 to 125 microns) per coat. Note: Number of coats and thickness requirements will vary with substrate, application method and exposure. Contact your Tnemec representative. Unthinned: 0.82 lbs/gallon (99 grams/litre)
Thinned 10% (No. 68 Thinner): 0.82 lbs/gallon (99 grams/litre)
Thinned 10% (No. 49 Thinner): 0.82 lbs/gallon (99 grams/litre) †
Two: Part A and Part B
Series 73 | Endura-Shield Aliphatic Acrylic Polyurethane
Hide this product's data
Volume Solids Rec. DFT V.O.C. # of Components
58.0 ± 2.0% (mixed) † 2.0 to 5.0 mils (50 to 125 microns) per coat. Note: Number of coats and thickness requirements will vary with substrate, application method and exposure. Contact your Tnemec representative.
UnthinnedThinned 10% (Max) (No. 39 Thinner)Thinned 10% (Max) (No. 42 Thinner)Thinned 10% (Max) (No. 48 Thinner)Thinned 10% (Max) (No. 56 Thinner)Thinned 10% (Max) (No. 63 Thinner)
2.70 lbs/gallon (324 grams/litre)3.05 lbs/gallon (366 grams/litre)3.10 lbs/gallon (371 grams/litre)3.15 lbs/gallon (378 grams/litre)2.76 lbs/gallon (331 grams/litre)3.07 lbs/gallon (368 grams/litre)

Two: Part A and Part B
Series 1075 | Endura-Shield II Aliphatic Acrylic Polyurethane
Hide this product's data
Volume Solids Rec. DFT V.O.C. # of Components
71 ± 2.0% (mixed) † 2.0 to 5.0 mils (50 to 125 microns) per coat. Note: Number of coats and thickness requirements will vary with substrate, application method and exposure. Contact your Tnemec representative. EPA Method 24 †
Unthinned Maximum 15%
(No. 39 Thin.)
Max 15%
(No.42 Thin.)
Max 15%
(No. 48 Thin.)
Max 15%
(No. 56 Thin.)
Max 15%
(No. 63 Thin.)
1.84 lbs/gal (220 g/l) 2.42 lbs/gal (290 g/l) 2.48 lbs/gal (297 g/l) 2.55 lbs/gal (305 g/l) 1.94 lbs/gal (232 g/l) 2.54 lbs/gal (305 g/l)
Two: Part A and Part B
Series 1081 | Endura-Shield Waterborne Acrylic Polyurethane
Hide this product's data
Volume Solids Rec. DFT V.O.C. # of Components
61.0 ± 2.0% (mixed) † 2.0 to 3.0 mils (50 to 75 microns) per coat. Note: Number of coats and thickness requirements will vary with substrate, application method, and exposure. Caution: Application of coating below minimum or above maximum recommended dry film thicknesses may adversely affect coating aesthetics and performance. Excessive film thicknesses will cause microbubbling. Contact your Tnemec representative. Unthinned: 0.73 lbs/gallon (88 grams/litre)
Thinned 5% (Water): 0.73 lbs/gallon (88 grams/litre)
Thinned 5% (No. 66 Thinner): 1.23 lbs/gallon (147 grams/litre) †
Two: Part A and Part B