find your coatings consultants
Find and contact a coatings consultant near you.

Series 217 | MortarCrete

Generic Type Cementitious Repair Mortar
Common Usage A single-component, rapid setting, hydraulic cementitious resurfacer used to restore deteriorated concrete surfaces.
Colors Gray
Primers Concrete: Series 217 Bond Coat †
† A thin bond coat (scrub coat) is required. Refer to the Series 217 MortarCrete Surface Preparation and Application Guide or Contact Tnemec Technical Services with questions.
Topcoats Series 22, FC22, 27WB, 46H-413, L69, L69F, N69, N69F, V69, V69F, 120, L140, L140F, N140, N140F, V140, V140F, 201, 215, 218, 237SC, 239SC, 434, 435, 436, 446
Note: Series 217 must be mechanically prepared in accordance with SSPC-SP13/NACE 6, ICRI-CSP4-5 surface profile prior to application of recommended topcoats. Shrinkage cracks in the Series 217 may require filling with Series 215 or Series 218 to prevent transfer or telegraphing of any cracks. Contact Tnemec Technical Services for additional information.
Recommended DFT Horizontal/Vertical: 1/4 inch (6 mm) to 4 inches (102 mm)
Overhead: 1/4 inch (6 mm) to 2 inches (51 mm)
Curing Time
Temperature Initial Set Final Set To Topcoat
70°F (21°C) 60 minutes 90 minutes 12 hours

Note: Use Series 211-217 Slow Set additive to extend set times. Refer to Series 211-217 Slow Set product data sheet for information.
Volatile Organic Compounds 0.0 lbs/gallon (0 grams/litre)
Number of Components One: 2.4 gallons/0.3 cu ft (9.0 L) (dry volume) approximately
1
Category
2
Chemical Name(required)
3
Concentration
4
What is this?

Note: Not Recommended (NR), Not Tested (NT), Please Call (PC)

 

Chemical Recommended Use - What is this?

The chemical resistance data listed on this website should only be used for general reference purposes. Substrates, temperatures, chemical combinations, and other variables can affect the performance of a coating in chemical exposure. Please contact your local to finalize the most appropriate system for your project.

Click the following button to download a PDF of the list of chemicals below.

1 Product is NOT suitable for direct or indirect food contact. Intended Use and temperature information relates    to product's performance capabilities only.

2 Product is suitable for direct or indirect food contact. Reference the product data sheet for more information.


Recommended Use
Chemical Occasional Contact Frequent Contact Secondary Containment Cargo Immersion Immersion Service

1 Product is NOT suitable for direct or indirect food contact. Intended Use and temperature information relates    to product's performance capabilities only.

2 Product is suitable for direct or indirect food contact. Reference the product data sheet for more information.

  • Color cards, swatches and fan decks are offered at no charge, by request , for more accurate color selection. Expert custom color matching is also available by contacting your Tnemec Coatings Consultant .
  • Deeptone colors may be more expensive than lighter colors. Please contact your Tnemec Coatings Consultant to verify product/color availability and pricing.
These digital colors should not be used to finalize your color selection. Please read our disclaimer . Use the color swatch tool on the left to request official color swatches.

Color Swatch Packet

Request another

(maximum 6 color swatches)

You haven't added any color swatches to your packet. Select some colors now by clicking a color above and then clicking the 'Request a Swatch' button on the color.

The products listed below are not exact equivalents. They are only products that you may consider as alternatives in a general sense. Substrate type, condition, temperatures, surface preparation, primer/topcoat selection and intended use are just a few factors that will affect product selection. Please contact your local Tnemec Coatings Consultant for product recommendations.

This ProductCementitious Repair Mortar

GET THE LATEST NEWS AND UPDATES BY EMAIL FROM TNEMEC

support documents