Series 1070 | Fluoronar

Generic Type Advanced Thermoset Solution Fluoropolymer
Common Usage A high-solids fluoropolymer coating that provides an ultra-durable finish with user friendly brush, roll and conventional spray application. It has outstanding color and gloss retention even in the most severe exposures. Under certain conditions, it may be used to restore aged fluoropolymer coil applied coatings or for OEM applications. Contact Tnemec Technical Services or your local Tnemec representative for details.
Colors Refer to Tnemec Color Guide. Note: Certain colors may require multiple coats depending on method of application and finish coat color. The preceding coat should be in the same color family, but noticeably different. Upon selection of the finish coat color (Series 1070), the intermediate coat color will be selected by Tnemec's color lab.
Finish Gloss
Primers Series 1, 27, 66, L69, L69F, N69, N69F, V69, V69F, 90-97, H90-97, 91-H2O, 94-H2O, 135, 161, 394. Note: Series 1 and 394 require an intermediate coat prior to topcoating with Series 1070.
Intermediate Series 73, 750, 1075, 1075U (Intermediate coat may be required for some applications, please contact Tnemec.) Note: When topcoating with Series 1070, the following maximum recoat times apply: Over 27, 66, L69, L69F, N69, N69F, V69, V69F, 135 or 161, 14 days; over itself, 30 days; over 750, 45 days; over 73, 90-97, H90-97, 91-H2O, 94-H2O, 1075 and 1075U, 90 days.
Volume Solids 60.0 ± 2.0% (mixed) †
Recommended DFT 2.0 to 3.0 mils (50 to 75 microns) per coat. Note: Number of coats and thickness requirements will vary with substrate, application method and exposure. Contact your Tnemec representative.
Curing Time
Temperature To Touch To Handle Minimum Recoat ‡
90°F (32°C) 10 minutes 4 hours 5-8 hours
70°F (21°C) 30 minutes 6-8 hours 10-12 hours
50°F (10°C) 1 hour 12-15 hours 16-24 hours
‡ Maximum recoat: 30 days. Curing time varies with surface temperature, air movement, humidity and film thickness. Note: For faster curing and low-temperature applications, add No. 44-710 Urethane Accelerator; see separate product data sheet.
Volatile Organic Compounds Unthinned: 2.93 lbs/gallon (351 grams/litre)
Thinned 5% (No. 63 Thinner): 3.10 lbs/gallon (371 grams/litre) †
HAPS Unthinned: 4.1 lbs/gal solids
Theoretical Coverage 962 mil sq ft/gal (23.6 m²/L at 25 microns). †
Number of Components Two: Part A and Part B

The products listed below are not exact equivalents. They are only products that you may consider as alternatives in a general sense. Substrate type, condition, temperatures, surface preparation, primer/topcoat selection and intended use are just a few factors that will affect product selection. Please contact your local Tnemec Coatings Consultant for product recommendations.

This ProductAdvanced Thermoset Solution Fluoropolymer
Volume SolidsRec. DFTV.O.C.# of Components
60.0 ± 2.0% (mixed) †2.0 to 3.0 mils (50 to 75 microns) per coat. Note: Number of coats and thickness requirements will vary with substrate, application method and exposure. Contact your Tnemec representative.Unthinned: 2.93 lbs/gallon (351 grams/litre)
Thinned 5% (No. 63 Thinner): 3.10 lbs/gallon (371 grams/litre) †		Two: Part A and Part B
Series 1071 | Fluoronar Advanced Thermoset Solution Fluoropolymer
Hide this product's data
Volume SolidsRec. DFTV.O.C.# of Components
60.0 ± 2.0% (mixed) †2.0 to 3.0 mils (50 to 75 microns) per coat. Note: Number of coats and thickness requirements will vary with substrate, application method and exposure. Contact your Tnemec representative.EPA Method 24 †
Unthinned: 2.65 lbs/gallon (317 grams/litre)
Thinned 5% (No. 63 Thinner): 2.82 lbs/gallon (338 grams/litre)
Thinned 5% (No. 56 Thinner): 2.95 lbs/gallon (353 grams/litre) 		Two: Part A and Part B
Series 1072 | Fluoronar Advanced Thermoset Solution Fluoropolymer
Hide this product's data
Volume SolidsRec. DFTV.O.C.# of Components
60.0 ± 2.0% (mixed) †2.0 to 3.0 mils (50 to 75 microns) per coat. Note: Number of coats and thickness requirements will vary with substrate, application method and exposure. Contact your Tnemec representative.EPA Method 24 †
Unthinned: 2.40 lbs/gallon (288 grams/litre)
Thinned 5% (No. 63 Thinner): 2.81 lbs/gallon (337 grams/litre)
Thinned 5% (No. 56 Thinner): 2.68 lbs/gallon (321 grams/litre)		Two: Part A and Part B
Series 1078 | Fluoronar Metallic Advanced Thermoset Solution Fluoropolymer
Hide this product's data
Volume SolidsRec. DFTV.O.C.# of Components
54.0 ± 2.0% (mixed) †2.0 to 3.0 mils (50 to 75 microns) per coat.Unthinned: 3.40 lbs/gallon (407 grams/litre)
Thinned 15% (No. 63 Thinner): 3.80 lbs/gallon (454 grams/litre) †		Two: Part A and Part B

Email this product

Series 1070 Fluoronar was used on the Great America Place Trellis in Santa Clara, CA.

Support Documents

View all support documents