Series L69 | Hi-Build Epoxoline II

Generic Type Polyamidoamine Epoxy
Common Usage A versatile low VOC epoxy for protection and finishing of steel and concrete. It has excellent resistance to abrasion and is suitable for immersion as well as chemical contact exposure. Contact your local Tnemec representative for a list of chemicals. This product can also be used for lining storage tanks that contain demineralized, deionized or distilled water. Can also be used as a block filler on cementitious or masonry substrates.
Colors Refer to Tnemec Color Guide. Note: Epoxies chalk with extended exposure to sunlight. Lack of ventilation, incomplete mixing, miscatalyzation or the use of heaters that emit carbon dioxide and carbon monoxide during application and initial stages of curing may cause yellowing to occur.
Finish Satin
Surfacer/Filler/Patcher 215
Primers Steel: Self-priming or Series 1, 27, 37H, 66, L69F, N69, N69F, V69, V69F, 90E-92, 90G-1K97, 90-97, H90-97, 90-98, 91-H2O, 94-H2O, 135, 161, 394, 530
Galvanized Steel and Non-Ferrous Metal: Self-priming or Series 66, L69F, N69, N69F, V69, V69F, 161
Concrete: Self-priming or Series 130, 215, 218
CMU: Self-priming or Series 130, 215, 218, 1254
Topcoats 22, 46H-413, 66, L69, L69F, N69, N69F, V69, V69F, 72, 73, 84, 104, 113, 114, 141, 156, 157, 161, 175, 180, 181, 287, 446, 740, 750, 1028, 1029, 1070, 1070V, 1071, 1071V, 1072, 1072V, 1074, 1074U, 1075, 1075U, 1077, 1078, 1080, 1081. Refer to COLORS on applicable topcoat data sheets for additional information. Note: The following recoat times apply for Series L69: Immersion Service—Surface must be scarified after 60 days. Atmospheric Service—After 60 days, scarification or an epoxy tie-coat is required. When topcoating with Series 740 or 750, recoat time for L69 is 21 days for atmospheric service. Contact your Tnemec representative for specific recommendations.
Volume Solids 65.0 ± 2.0% (mixed) †
Recommended DFT 2.0 to 10.0 mils (50 to 255 microns) per coat. Note: MIL-PRF-4556F applications require two coats at 4.0-6.0 mils (100-150 microns) per coat. Otherwise, the number of coats and thickness requirements will vary with substrate, application method and exposure. Contact your Tnemec representative.
Volatile Organic Compounds Unthinned: 0.82 lbs/gallon (98 grams/litre)
Thinned 5%: 0.82 lbs/gallon (98 grams/litre)
TBAC (non-exempt): 1.09 lbs/gallon (130 grams/litre) †
HAPS Unthinned: 0 lbs/gal solids
Thinned 5%: 0 lbs/gal solids
Theoretical Coverage 1,043 mil sq ft/gal (25.6 m²/L at 25 microns). See APPLICATION for coverage rates. †
Number of Components Two: Part A (amine) and Part B (epoxy) — One (Part A) to one (Part B) by volume
  • Color cards, swatches and fan decks are offered at no charge, by request, for more accurate color selection. Expert custom color matching is also available by contacting your Tnemec Coatings Consultant.
  • Deeptone colors may be more expensive than lighter colors. Please contact your Tnemec Coatings Consultant to verify product/color availability and pricing.

Products Available In Vapor Mist 01GR

Vapor Mist| 01GR rgb 211,211,216
Request a Swatch Swatch Unavailable
These digital colors should not be used to finalize your color selection. Please read our disclaimer. Use the color swatch tool on the left to request official color swatches.

Color Swatch Packet

remove all swatches

(maximum 6 color swatches)

You haven't added any color swatches to your packet. Select some colors now by clicking a color above and then clicking the 'Request a Swatch' button on the color.

The products listed below are not exact equivalents. They are only products that you may consider as alternatives in a general sense. Substrate type, condition, temperatures, surface preparation, primer/topcoat selection and intended use are just a few factors that will affect product selection. Please contact your local Tnemec Coatings Consultant for product recommendations.

This ProductPolyamidoamine Epoxy
Volume SolidsRec. DFTV.O.C.# of Components
65.0 ± 2.0% (mixed) †2.0 to 10.0 mils (50 to 255 microns) per coat. Note: MIL-PRF-4556F applications require two coats at 4.0-6.0 mils (100-150 microns) per coat. Otherwise, the number of coats and thickness requirements will vary with substrate, application method and exposure. Contact your Tnemec representative.Unthinned: 0.82 lbs/gallon (98 grams/litre)
Thinned 5%: 0.82 lbs/gallon (98 grams/litre)
TBAC (non-exempt): 1.09 lbs/gallon (130 grams/litre) †		Two: Part A (amine) and Part B (epoxy) — One (Part A) to one (Part B) by volume
Series N69 | Hi-Build Epoxoline II Polyamidoamine Epoxy
Hide this product's data
Volume SolidsRec. DFTV.O.C.# of Components
67.0 ± 2.0% (mixed) †2.0 to 10.0 mils (50 to 255 microns) per coat. Note: MIL-PRF-4556F applications require two coats at 4.0-6.0 mils (100-150 microns) per coat. Otherwise, the number of coats and thickness requirements will vary with substrate, application method and exposure. Contact your Tnemec representative.N69 - Unthinned: 2.40 lbs/gallon (285 grams/litre) V69 - Unthinned: 1.95 lbs/gallon (234 grams/litre)
Thinned 10% (No. 4 Thinner): 2.80 lbs/gallon (334 grams/litre) Thinned 2.5%: 2.08 lbs/gallon (250 grams/litre) †
Thinned 10% (No. 60 Thinner): 2.80 lbs/gallon (335 grams/litre)
Two: Part A (amine) and Part B (epoxy) — One (Part A) to one (Part B) by volume.

Email this product

The North Hollywood Gateway support structure received a shop-applied prime coat of Series L69 Hi-Build Epoxoline II.

Support Documents